BENDIX BW2718 Manual do Utilizador

1Bendix® TABS‑6™ Advanced Single‑Channel Trailer ABS Module1. INTRODUCTIONThe Bendix® TABS‑6™ Adv module is an integrated single‑channel (2S/1M) trail

1013. BENDIX® ABS FLEX™ PROGRAMThe BendixABS Flex program usesAuxiliary DesignLanguage(ADL) toallowcustomizedauxiliary functionsto be c

1117. NON‑STANDARD TIRE SIZEThe Bendix® TABS‑6™ Adv module allows for tire rolling radius and tone ring tooth count parameters to be set for the axle

12Wait until after the modulator chuff test before activating thebrakelightpower.Alternatively,waitve(5)seconds.Note: If certain Diagnostic

1322. DIAGNOSTIC TROUBLE CODES (DTCS)1st Digit2nd DigitDiagnostic Code DescriptionPossible Causes / Repair InformationJ1587 (SID/FMI)J1939(SPN/FMI)1

14Diagnostic Trouble Codes (DTCs) (continued)1st Digit2nd DigitDiagnostic Code DescriptionPossible Causes / Repair InformationJ1587 (SID/FMI)J1939 (SP

15Diagnostic Trouble Codes (DTCs) (continued)1st Digit2nd DigitDiagnostic Code DescriptionPossible Causes / Repair InformationJ1587 (SID/FMI)J1939 (SP

16Diagnostic Trouble Codes (DTCs) (continued)1st Digit2nd DigitDiagnostic Code DescriptionPossible Causes / Repair InformationJ1587 (SID/FMI)J1939 (SP

17Diagnostic Trouble Codes (DTCs) (continued)1st Digit2nd DigitDiagnostic Code DescriptionPossible Causes / Repair InformationJ1587 (SID/FMI)J1939 (SP

18USING HAND‑HELD ORPC‑BASED DIAGNOSTICSTroubleshooting and Diagnostic Trouble Code (DTC)clearing,aswellasbeginningareconguration,mayals

19How the Bendix® TRDU™ Tool OperatesWhentheTRDUtoolispluggedintotheadapter—andtheadapter/TRDUtoolisinstalledbetweenthetrailerconne

2● Anextendeddataloggingfeature,includingaresettabledrive recorder.● Awidevarietyofelectricalinputs/outputs(I/Os)allowthe customer t

20To better serve you, please record the following information before you call the Bendix Tech Team, or include this information in your e‑mail:• Ben

211. The TABS‑6 Adv module shall be installed with the followingconsiderations(seeFigures16through18):5°5°VERTICAL ORIENTATION (ROLL ANGLE)MUST

22FIGURE 19 ‑ WHEEL SPEED SENSOR INSTALLATIONLEAKAGE AND OPERATIONAL TESTS1. Before performing the leakage tests, block the wheels.2. Fully charge t

23• Pressure Sensor Test: Duringthistest,checksarecarried out that verify that the proper response is received from the pressure sensors during

242131714816410153917115126182121121243211234432112345566432112342176544567321213174S-DS-C X1 “ECU”FIGURE 20 ‑ BENDIX® TABS- 6™ ADV MODULE ELECTRICAL

25FIGURE 22 - BENDIX® TABS- 6™ ADV MODULE - 2S/1M AXLE CONTROL (0 DEGREE) ABS ELECTRICAL & AIR SYSTEMFIGURE 23 - BENDIX® TABS- 6™ ADV MODULE - 2S/

26Troubleshooting: System SchematicsFIGURE 24 - BENDIX® TABS- 6™ ADV MODULE - 2S/1M AXLE CONTROL (0 DEGREE) WITH REAR LIFT AXLE, ABS ELECTRICAL &

27SectionA:(Power-UpSequence)Trailer‑Mounted ABS Indicator Lamp ...Page 27SectionB:(Power-UpSequence)Dash‑Mounted ABS Indicator La

28Observethedash-mountedTrailerABSIndicatorLampatPower-UpVerifythataPLCtrailerisconnectedto the tractor via the 7‑pin connector. Turnt

29SECTION C: TROUBLESHOOTING THE TRAILER‑MOUNTEDABS INDICATOR LAMP CIRCUITRYThe trailer‑mounted ABS indicator lamp did not illuminate during the power

33. ANTILOCK BRAKE SYSTEM (ABS) OPERATIONThe Bendix® TABS‑6™ Adv module uses wheel speed sensors, modulator relay valve(MRV);and an ECUtoop

30SECTION D: TROUBLESHOOTING THEPOWER SUPPLYTurn off the power to the module, disconnectthe18-pinECUconnector.Checkforhighresistance(corrosion

31SECTION E: TROUBLESHOOTING THEBENDIX® WS‑24™ WHEEL SPEED SENSORS (WSS)Turn off the power to the module, disconnect the wheel speed sensor connector.

32SECTION F: TROUBLESHOOTING THELOAD SENSOR (OUT‑OF‑RANGE CONDITION)(Note: The indicator lamp for this condition is illuminated only after the vehicl

331.CheckthattheElectronicControlUnit(ECU)isinstalledcorrectly(expectedorientationtovehicle).EachBendix® TABS‑6™AdvancedECUcomespr

34ECU Part Number LabelThe external part number label is located above the control port of the module. If this label is not readable for any reason,

35NOTES

36SD‑13‑47671_US_001©2013BendixCommercialVehicleSystemsLLC,amemberoftheKnorr-BremseGroup•AllRightsReserved•6/13Log-on and Learn fr

44. BENDIX® TRAILER ROLL STABILITY PROGRAM (TRSP®) OPERATION WARNING! During a Bendix® TRSP® system intervention, the vehicle automatically decelerat

55. COMPONENTSInstallations of the TABS‑6 Adv module use the following components:Internal:• Electronic Control Unit (ECU): TheECUmonitorsthe spe

6• Pigtail Wiring Harness: A power pigtail harness is required,variationsthatincludeauxiliarysub-harnessesare available, as needed. See Figur

76. MOUNTING CONFIGURATIONSTank (Nipple) MountThe TABS‑6 Advanced module can be tank‑mounted using aschedule80(heavygaugesteel)3/4”NPTnipple

8CAUTION: Correct wheel speed sensor installation is necessary for optimal ABS operation.Sensors should not be installed on a lift axle.1. For increa

910. SAE J2497 (PLC) DIAGNOSTIC LINKAll newer towed vehicles transmit a signal over the power linetothetowingvehicleABSECU.Thesignal,using